Reverse and Brake LED light kit
Reverse and Brake LED light kit for S550 Ford Performance Tow Hook
Warranty
* 5 Year warranty on LEDs by ECCO
Specs
* 1.2 amps White (3 LEDs)
* 1.2 amps Red (3 LEDs)
About
These are made to order. They are 3 week turnaround. More information will be posted soon. Mounts to OEM reverse light area on rear bumper. Comes everything needed to tap into factory wires.
INSTRUCTIONAL VIDEO
VIDEO COMING SOON...
CONTENTS:
-
4 T-Taps
-
2 Aerospace grade aluminum brackets
-
2 ECCO ED9040 RED/WHITE LED 1 inch strobe pods
-
Red 12 ½ ft 16 GA Tinned Copper Wire (Marine Grade)
LED Light wire colors:
-
Red: (+) 12V input for red LEDs
-
White: (+) 12V input for white LEDs
-
Black: (-) ground input for all LEDs
-
Blue: Programming input (not needed)
-
Yellow: Sync connector (not needed)
Installation:
-
Remove the rear bumper using the installation instructions found on your FORD PERFORMANCE tow hook install guide.
-
Based on the tow hook install guide you will see that you will need to remove the foam support and the OEM reverse light.
-
There are 4 screws that mount the OEM reverse light to the valance/rear bumper. Use these 4 screws to mount the new brackets with the lights already mounted on them.
-
Below the mounting point you will find the plug for the OEM reverse light which has a ground (-) wire and a reverse light (+) output wire. Confirm these wires using a multimeter/12V circuit tester.
-
Using one of the supplied T-Taps, tap into the factory ground (-) wire about 1 inch away from the connector, and connect the black ground input (-) wires coming out of the LED lights. Be sure that the male connector pin isn’t bent and that it slides in properly.
-
Using another one of the supplied T-Taps, tap into the reverse light (+) output wire 1 inch away from the connector, and connect the white (+) 12V input LED wire. Be sure that the male connector pin isn’t bent and that it slides in properly.
-
Connect the supplied red 16 GA wire to the red (+) 12V input LED wire and zip tie to OEM rear bumper wire harness leaving the additional length of wire coming out of the top of the bumper’s Left (driver’s) tail light area.
-
Confirm that all the connectors are plugged in properly and install the bumper back on the vehicle. Note that if you have an issue with wiring, access to the factory wires are now as easy as removing the OEM rear bumper diffuser.
-
Continue routing the supplied red (+) 12V wire inside the trunk by cutting a small hole on the rubber grommet found behind the driver side tail light.
-
Run the wire behind the carpet and against the side wall of the trunk using zip ties towards the factory 3rd brake light.
-
When you reach the factory speaker panel, you will find a small opening through which you can route the wire and access inside the driver rear pillar. Remove this pillar.
-
Zip tie the wire behind the airbag and avoid having it interfere with the airbag’s deployment in any way. Routing the wire in front of or wrapping around the airbag can cause injury or bodily harm during the deployment of airbags.
-
Finish routing the red (+) 12V wire to 3rd brake light and use the supplied T-Taps to tap into the factory 12V output wire.
-
Install rear driver pillar back on carefully as to not damage the clips. Installation is not complete.
PLEASE NOTE: The factory body control module contains a safety feature that shuts off each light individually is there is a short circuit. For example, if the third brake light somehow short circuits, the body control module will shut off power to the third brake light only and so forth. Therefore do not be alarmed to see that our kit does not contain any fuses.
-
DISCLAIMER
Check your tail lights, brake lights and reverse lights regularly as should be done with factory and aftermarket lights. By purchasing and installing these lights you accept liability resulting from improper installation and improper usage and/or maintenance of these LED lights. You release Bemaro, Inc. from any liability resulting from improper installation and improper usage and/or maintenance of these LED lights. In no event shall Bemaro, Inc. be liable for any direct, indirect, punitive, incidental, special consequential damages, to property or life, whatsoever arising out of or connected with the use or misuse of our products. For more information about this kit please contact us at 714-900-1770.